親：

1.可免費為客戶檢測試樣；

2.可以根據不同客戶的需求進行訂做產品。

3.售前，我們專門派技術人員為您設計*的流程和方案；

4.信后，將免費指派技術人員為您調試安裝；

5.保修一年，產品終身維護；

6.常年供應設備的易損件及耗品，以確保產品長期使用。

北京冠測試驗儀器有限公司專注于試驗方法的創新及應用，是集研發、生產、銷售、售后于一體的專業試驗儀器供應商！

咨詢洽談業務!

建筑材料可燃性試驗儀

編號：GD201311030063

規格：JZKR-A

建筑材料可燃性試驗儀

產品名稱：建筑材料可燃性試驗儀

產品型號：JZKR-A

主要用途：

適用于在規定的條件下判定建筑材料是否具有可燃性。

建筑材料可燃性試驗儀技術指標：

1、噴嘴孔徑：￠0.17+0.03mm

2、火焰高度：20±1mm

3、點火器計時：0～99.99秒任意設置

4、使用氣體：純度在95%以上的丙烷氣

5、試樣尺寸：250mm×90mm

6、點火定位裝置

7、融化滴落制品的試樣夾

建筑材料可燃性試驗儀適用標準：

GB/T 8626-2007 《建筑材料可燃性試驗方法》

ISO 11925-2：2002

建筑材料可燃性試驗儀操作方法

1、使用250mm×90mm的模板切割試樣。如果試樣為融化收縮制品，則選用250mm×180mm的模板。

2、將試樣夾在尺寸為250mm×90mm試樣夾內，擰緊蝶母，固定好試樣。融化收縮制品樣夾尺寸為250mm×180mm。此時試樣夾先不要裝到水平桿上。

3、打開電源開關，將點火時間設的稍長一些，比如5min。根據點火方式選擇相應的定位器，按試驗開始，燃燒器在45°位置停止后，將定位器的一端插入燃燒器中。此時將試樣夾裝到水平桿上，調節試樣夾的上下左右位置，使其符合試驗要求。將定位器取出。按返回鍵。等燃燒器復位后，按試驗清零。

4、長按點火鍵，同時調節儀器面板上的火焰調節閥，點著氣體后，再調節火焰高度到20士1mm，將火焰從大調到小時，先將面板上的火焰調節旋鈕背緊，再調節火焰會比較容易。測高尺高度20mm。關閉前門。

5、將收集盤內放兩張濾紙，然后將其放在試樣下方。

6、設定點火時間，按試驗開始，燃燒器自動轉到45°位置，并在該位置停留設定的點火時間，然后復位，同時續燃時間開始計時。在試樣續燃未達到刻度線前停止續燃后，按下續燃停止或試樣續燃達到刻度線后立即按下續燃停止。記錄燃燒時間。

7、按試驗清零，停止試驗。如想繼續進行試驗可重復以上步驟，否則關閉電源。

為了滿足客戶需要整理了英文資料，親請參閱哦！

Building materials flammability test instrument

Number: GD201311030063

Specification: JZKR-A

Building materials flammability test instrument

Product Name: building materials flammability test instrument

Product type: JZKR-A

Main uses:

Applicable to the specified conditions to determine whether a combustible building materials.

Building materials Flammability Tester technical indicators:

1, the nozzle diameter: - 0.17+0.03mm

2, the flame height: 20 ± 1mm

3, the ignition timing: 0 ~ 99.99 seconds set

4, the use of gas: purity more than 95% propane gas

5, the sample size: 250mm x 90mm

6, the ignition location device

Sample 7, melt dripping products clip

Building materials flammability test instrument for standard:

GB/T 8626-2007 "test method of flammability for building materials"

ISO 11925-2:2002

=========================================

The operation method of building materials flammability test instrument

Sample 1, using the 250mm * 90mm template cutting. If the sample is melted contraction product, choose 250mm x 180mm template.

2, the sample size of 250mm * 90mm in the specimen holder, tighten the butterfly nut, fixed specimens. Melting shrinkage products like clip size is 250mm × 180mm. The sample holder should not be attached to the horizontal bar.

3, turn on the power switch, the ignition time is slightly longer, such as 5min. According to the ignition mode select positioner, according to the test, the burner at 45 ° position after the stop, the locator is inserted into the burner. The sample is clamped to the horizontal rod, adjustable sample holder on the left and right position, to meet the testing requirements. The locator out. Press the return key. Burner after reset, reset according to the test.

4, long press the ignition key, while adjusting the instrument panel on the flame regulating valve, a gas, then adjust the flame height to 20 ± 1mm, the flame from major to hours, the best first panel on the flame adjusting knob back tightly, then adjust the flame will be easier. Altimeter scale height 20mm. Close the front door.

5, will collect the tray placed two pieces of filter paper, and then put it in the sample.

6, set the ignition time, according to the test, automatic burner to the position of 45 DEG, and stays at the position the ignition time, the set and reset, and continued ignition timing starts. In the sample continued burning did not reach the scale line before the end of the continued burning, press the continued burning stop or sample continued burning reach scale line immediay after the press continued burning stop. To record the burning time.

7, according to tests cleared, stop test. If you want to continue testing can repeat the above steps, or turn off the power.